1 | GUI module:␊ |
2 | ----------␊ |
3 | GUI=No Disable the GUI (Enabled by default).␊ |
4 | "Boot Banner"=Yes|No Show boot banner in GUI mode (Enabled by default).␊ |
5 | "Legacy Logo"=Yes|No Use the legacy grey apple logo (Disabled by default).␊ |
6 | RandomTheme=Yes|No Enable/Disable switching skin randomly at boot time(Disabled by default).␊ |
7 | ␊ |
8 | ␊ |
9 | GraphicsEnabler module:␊ |
10 | ----------------------␊ |
11 | EnableGFXModule=Yes|No Fully enable/disable the GraphicsEnabler module (Enabled by default, if the module is installed)␊ |
12 | ␊ |
13 | UseAtiROM=Yes|No Use an alternate Ati ROM image ␊ |
14 | (path: /Extra/<vendorid>_<devid>.rom)␊ |
15 | UseNvidiaROM=Yes|No Use an alternate Nvidia ROM image ␊ |
16 | (path: /Extra/<vendorid>_<devid>.rom)␊ |
17 | VBIOS=Yes|No Inject VBIOS to device-properties.␊ |
18 | ␊ |
19 | ␊ |
20 | Networking module:␊ |
21 | -----------------␊ |
22 | EnableNetworkModule=Yes|No␉Fully enable/disable the Networking module (Enabled by default, if the module is installed)␊ |
23 | ␊ |
24 | EthernetBuiltIn=Yes|No␉␉Automatic "built-in"=yes device-properties generation␊ |
25 | ␉␉␉␉␉␉␉␉for ethernet interfaces. (Enabled by default)␊ |
26 | ␊ |
27 | EnableWifi=Yes|No␉␉␉␉Enable wifi device-properties generation, if detected. (Enabled by default)␊ |
28 | ␊ |
29 | ␉␉␉␉␉␉ ␊ |
30 | Memory module:␊ |
31 | -------------␊ |
32 | EnableMemoryModule=Yes|No␉ Fully enable/disable the Memory module (Enabled by default, if the module is installed)␊ |
33 | ␊ |
34 | USBFix module:␊ |
35 | ----------␊ |
36 | EnableUSBModule=Yes|No␉ Fully enable/disable the USB module (Enabled by default, if the module is installed)␊ |
37 | ␉␊ |
38 | USBBusFix=Yes|No Enable all USB fixes below (except EHCIhard): (Enabled by default)␊ |
39 | EHCIacquire=Yes|No Enable the EHCI fix .␊ |
40 | UHCIreset=Yes|No Enable the UHCI fix .␊ |
41 | USBLegacyOff=Yes|No Enable the USB Legacy fix .␊ |
42 | ␊ |
43 | EHCIhard = Yes|No␉␉␉ Try EHCI soft reset (Disabled by default)␊ |
44 | ␊ |
45 | HPET module:␊ |
46 | -----------␊ |
47 | EnableUSBModule=Yes|No␉ Fully enable/disable the HPET module (Enabled by default, if the module is installed)␊ |
48 | ␊ |
49 | HibernateEnabler:␊ |
50 | ----------------␊ |
51 | EnableHibernateModule=Yes|No␉ Fully enable/disable the HibernateEnabler module (Enabled by default, if the module is installed)␊ |
52 | ␊ |
53 | Wake=No␉␉␉␉␉␉Disable wake up after hibernation (default: enabled).␊ |
54 | ForceWake=Yes␉␉␉␉␉Force using the sleepimage (Disabled by default).␊ |
55 | WakeImage=<file>␉␉␉␉Use an alternate sleepimage file. ␊ |
56 | ␉␉␉␉␉␉␉␉(default path is /private/var/vm/sleepimage).␊ |
57 | ␊ |
58 | SMBIOS modules:␊ |
59 | --------------␊ |
60 | SMBIOS=<file> Use an alternate SMBIOS.plist file ␊ |
61 | (default path: /Extra/SMBIOS.plist, ␊ |
62 | ␉␉␉␉␉␉bt(0,0)/Extra/SMBIOS.plist).␊ |
63 | ␊ |
64 | SMBIOSdefaults=Yes|No Don't use the Default values for SMBIOS overriding␊ |
65 | if smbios.plist doesn't exist, factory␊ |
66 | values are kept(Disabled by default).␊ |
67 | ␊ |
68 | RamDiskLoader module:␊ |
69 | -------------------- ␊ |
70 | EnableRamDiskLoader=Yes|No␉Fully enable/disable the RamDiskLoader module (Enabled by default, if the module is installed)␊ |
71 | ␊ |
72 | md0=<file>␉␉␉␉␉Load raw img file into memory for use as XNU's md0␊ |
73 | ␉␉␉␉␉␉␉␉ramdisk. /Extra/Postboot.img is used otherwise.␉␊ |
74 | ␉␉␉␉␉␉ ␊ |
75 | Keymapper module:␊ |
76 | ----------------␉␊ |
77 | EnableKeyMapper=Yes|No␉Fully enable/disable the Keymapper module (Enabled by default, if the module is installed)␊ |
78 | ␉␉␉␉␉ ␊ |
79 | KeyboardType=<value>␉␉change the type of the Keyboard. (Default is QWERTY)␊ |
80 | ␉␉␉␉␉␉␉for now only <value>="AZERTY" is supported.␊ |
81 | ␊ |
82 | CPUfreq module:␊ |
83 | --------------␊ |
84 | EnableCPUfreqModule=Yes|No␉Fully enable/disable the CPUfreq module (Enabled by default, if the module is installed)␊ |
85 | ␊ |
86 | FixFSB=Yes|No␉␉␉␉␉Enable alternative front side bus fix(Disabled by default).␊ |
87 | ␊ |
88 | MaxBusRatio=<n>␉(was BusRatio) Set the current Bus Ratio to n,␊ |
89 | ␉␉␉ n must be a multiple of 10,␊ |
90 | ␉␉␉ (eg. if you want to set a bus ratio to 8.5, n will be␊ |
91 | ␉␉␉ 8.5*10=85), ␊ |
92 | ␉␉␉ if n = 0, MaxBusRatio = Disable,␊ |
93 | ␉␉␉ if not set, n = the current␊ |
94 | ␉␉␉ bios bus ratio, set this value allow CPUfreq to ␊ |
95 | fix some cosmetic issues.␊ |
96 | ␉␉␉␉␉␉ ␉␉␉ ␊ |
97 | AcpiCodec module: ␊ |
98 | ------------------␊ |
99 | IMPORTANT NOTE: 1- with AcpiCodec all aml files must be placed in /Extra/Acpi/, alternate or overridden path is no longer supported␊ |
100 | ␊ |
101 | 2- the name of the aml file(s) is not important anymore but it must contain the extention .aml, for example let suppose that you have 3 aml files: dsdt.aml, ssdt-0.aml and ssdt-1.aml␊ |
102 | you can rename your dsdt file into blabla.aml, and rename your ssdt files into blablabla.aml and blablablabla.aml, acpicodec will auto-magically detect those files as 2 ssdt and one dsdt␊ |
103 | ␊ |
104 | EnableAcpiModule=Yes|No␉Fully enable/disable the Acpipatcher module (Enabled by default, if the module is installed)␊ |
105 | ␊ |
106 | RestartFix=Yes|No␉␉Enable/Disable internal restart fix patch (Enabled by default, only available for intel platform).␊ |
107 | ␊ |
108 | ResetType=0|1␉␉␉0 : PCI reset (Default)␊ |
109 | ␉␉␉␉1 : keyboard reset ␊ |
110 | ␊ |
111 | EnableSpeedStep=Yes|No␉Enable/Disable GenerateCStates & GeneratePStates (Disabled by default).␊ |
112 | ␊ |
113 | GeneratePStates=Yes|No␉Enable/Disable Generate P-states SSDT table (Disabled by default).␊ |
114 | GenerateCStates=Yes|No␉Enable/Disable Generate C-states SSDT table (Disabled by default).␊ |
115 | EnableC4State=Yes|No␉␉Enable C4 state in C-states SSDT table, GenerateCStates=Yes is needed (Disabled by default).␊ |
116 | ␊ |
117 | IntelFADTSpec=Yes|No␉␉Enable/Disable Intel recommendations for the FADT table (Enabled by default). ␊ |
118 | ␉␉␉␉Warning : When enabled, this setting disable the C2 and C3 C-states, but be aware that these are the Intel's recommendations for the newest CPU, ␊ |
119 | ␉␉␉␉␉ if you really need those c-states please disable IntelFADTSpec.␊ |
120 | ␊ |
121 | P-States=<dict>␉␉P-States fine tuning method, see usage below(GeneratePStates=Yes is needed).␊ |
122 | ACPIDropTables=<dict>␉␉drop acpi table(s) method (can drop any unwanted tables), see usage below.␊ |
123 | C-States=<dict>␉␉C-States fine tuning method, see usage below(GenerateCStates=Yes is needed).␊ |
124 | ␊ |
125 | ␉␉␉␉␉␉␉␊ |
126 | UpdateACPI=Yes|No Enable/Disable ACPI version update(Disabled by default). ␉␉␉ ␊ |
127 | ␊ |
128 | MaxBusRatio=<n>␉(was BusRatio) Set the current Bus Ratio to n, ␊ |
129 | ␉␉␉ n must be a multiple of 10,␊ |
130 | ␉␉␉␉␉(eg. if you want to set a bus ratio to 8.5, n will be␊ |
131 | ␉␉␉ 8.5*10=85), ␊ |
132 | ␉␉␉ if n = 0, MaxBusRatio = Disable,␊ |
133 | ␉␉␉ if set, Acpipatcher will drop every P-states with␊ |
134 | ␉␉␉ a bus ratio higher than n.␊ |
135 | ␉␉␉␉␉␉ ␊ |
136 | MinBusRatio=<n>␉Set the Minimum Bus Ratio to n,␊ |
137 | ␉␉␉ n must be a multiple of 10,␊ |
138 | ␉␉␉ (eg. if you want to set the bus ratio to 8.5, n will be␊ |
139 | ␉␉␉ 8.5*10=85), if set Acpipatcher will drop every ␊ |
140 | ␉␉␉ P-states with a bus ratio lower than n, ␊ |
141 | ␉␉␉ if n = 0, MinBusRatio = Disable.␊ |
142 | ␉␉ ␊ |
143 | P-States usage e.g: (by default all numbers must be expressed in base 16, ␊ |
144 | ␉␉␉ except the pss statue key and base key itself)␊ |
145 | ␉␉␊ |
146 | ␉␉<key>P-States</key>␊ |
147 | ␉␉<dict>␊ |
148 | ␉␉<key>0</key> // the pss status (must be expressed in Base 10)␊ |
149 | ␉␉<dict>␊ |
150 | ␉␉<key>Bus Master Latency</key>␊ |
151 | ␉␉<string>10</string>␊ |
152 | ␉␉<key>Control</key>␊ |
153 | ␉␉<string>18719</string>␊ |
154 | ␉␉<key>CoreFreq</key>␊ |
155 | ␉␉<string>3164</string>␊ |
156 | ␉␉<key>Transition Latency</key>␊ |
157 | ␉␉<string>10</string>␊ |
158 | ␉␉</dict>␊ |
159 | <key>1</key> // the pss status (must be expressed in Base 10)␊ |
160 | .␊ |
161 | .␊ |
162 | .␊ |
163 | ␉␉<dict/>␊ |
164 | ␉␉<key>2</key> // the pss status (must be expressed in Base 10)␊ |
165 | .␊ |
166 | .␊ |
167 | .␊ |
168 | ␉␉<dict/>␊ |
169 | <key>X</key> // the pss status (must be expressed in Base 10)␊ |
170 | .␊ |
171 | .␊ |
172 | .␊ |
173 | ␉␉<dict/>␊ |
174 | ␉␉<key>Base</key>␊ |
175 | ␉␉<string>10</string> // must always be expressed in Base 10 ␊ |
176 | ␉␉<key>Mode</key>␊ |
177 | ␉␉<string>Default</string>␊ |
178 | ␉␉</dict> ␉␊ |
179 | ␉␉␉␉␉␉␉␉␉ ␊ |
180 | ␊ |
181 | C-States usage e.g: (by default all numbers must be expressed in base 16, ␊ |
182 | ␉␉␉ except the base key itself)␊ |
183 | ␊ |
184 | ␉␉<key>C-states</key>␊ |
185 | ␉␉<dict>␊ |
186 | ␉␉<key>C1</key>␊ |
187 | ␉␉<dict>␊ |
188 | ␉␉<key>Latency</key>␊ |
189 | ␉␉<string>THE LATENCY FOR THIS STATE</string>␊ |
190 | ␉␉<key>Power</key>␊ |
191 | ␉␉<string>THE POWER FOR THIS STATE</string>␊ |
192 | ␉␉</dict>␊ |
193 | ␉␉.␊ |
194 | ␉␉.␉␉␉␉␉␉␉␊ |
195 | ␉␉<key>C4</key>␊ |
196 | ␉␉<dict>␊ |
197 | ␉␉<key>Latency</key>␊ |
198 | ␉␉<string>THE LATENCY FOR THIS STATE</string>␊ |
199 | ␉␉<key>Power</key>␊ |
200 | ␉␉<string>THE POWER FOR THIS STATE</string>␊ |
201 | ␉␉</dict>␊ |
202 | ␉␉</dict>␊ |
203 | ␉␉␊ |
204 | ACPIDropTables usage e.g: ␊ |
205 | ␊ |
206 | ␉␉<key>ACPIDropTables</key>␊ |
207 | ␉␉<dict>␊ |
208 | ␉␉<key>SSDT</key>␊ |
209 | ␉␉<string></string> // drop SSDT table(s)␊ |
210 | ␉␉<key>TAMG</key>␊ |
211 | ␉␉<string>Yes</string> //drop TAMG table␊ |
212 | ␉␉<key>ECDT</key>␊ |
213 | ␉␉<string>ANY_VALUE_EXCEPT_NO</string> //drop ECDT table␊ |
214 | ␉␉<key>XXXX</key>␊ |
215 | ␉␉<string></string> //drop XXXX table (if exist)␊ |
216 | ␉␉<key>YYYY</key>␊ |
217 | ␉␉<string>No</string> //do not drop YYYY table (if exist)␊ |
218 | ␉␉</dict>␊ |
219 | ␊ |
220 | ␊ |
221 | Acpipatcher module:␊ |
222 | ------------------␊ |
223 | EnableAcpiModule=Yes|No␉Fully enable/disable the Acpipatcher module (Enabled by default, if the module is installed)␊ |
224 | ␊ |
225 | RestartFix=Yes|No␉␉␉Enable/Disable internal restart fix patch(Enabled by default, only available for intel platform).␊ |
226 | ␊ |
227 | EnableSpeedStep=Yes|No␉Enable/Disable GenerateCStates & GeneratePStates (Disabled by default).␊ |
228 | ␊ |
229 | GeneratePStates=Yes|No␉Enable/Disable Generate P-states SSDT table (Disabled by default).␊ |
230 | GenerateCStates=Yes|No␉Enable/Disable Generate C-states SSDT table (Disabled by default).␊ |
231 | EnableC4State=Yes|No␉␉Enable C4 state in C-states SSDT table, GenerateCStates=Yes is needed (Disabled by default).␊ |
232 | ␊ |
233 | P-States=<dict>␉␉␉P-States fine tuning method, see usage below(GeneratePStates=Yes is needed).␊ |
234 | ACPIDropTables=<dict>␉␉drop acpi table(s) method (can drop any unwanted tables), see usage below.␊ |
235 | C-States=<dict>␉␉␉C-States fine tuning method, see usage below(GenerateCStates=Yes is needed).␊ |
236 | ␊ |
237 | DSDT=<file> ␉Use an alternate DSDT.aml file,␊ |
238 | ␉␉␉ (default path: /DSDT.aml Extra/DSDT.aml,␊ |
239 | ␉␉␉ bt(0,0)/Extra/DSDT.aml).␊ |
240 | ␊ |
241 | quickSSDTsearch=Yes|No If Yes, Acpipatcher will not search ssdt-(x+1).aml ␊ |
242 | ␉␉␉ if ssdt-x.aml do not exist,␊ |
243 | ␉␉␉ (eg. if ssdt-0.aml do not exist,␊ |
244 | Acpipather will not search ssdt-1.aml)(Enabled by default).␊ |
245 | ␉␉␉␉␉␉␉␊ |
246 | UpdateACPI=Yes|No Enable/Disable ACPI version update(Disabled by default). ␉␉␉ ␊ |
247 | ␊ |
248 | MaxBusRatio=<n>␉(was BusRatio) Set the current Bus Ratio to n, ␊ |
249 | ␉␉␉ n must be a multiple of 10,␊ |
250 | ␉␉␉␉␉(eg. if you want to set a bus ratio to 8.5, n will be␊ |
251 | ␉␉␉ 8.5*10=85), ␊ |
252 | ␉␉␉ if n = 0, MaxBusRatio = Disable,␊ |
253 | ␉␉␉ if set, Acpipatcher will drop every P-states with␊ |
254 | ␉␉␉ a bus ratio higher than n.␊ |
255 | ␉␉␉␉␉␉ ␊ |
256 | MinBusRatio=<n>␉Set the Minimum Bus Ratio to n,␊ |
257 | ␉␉␉ n must be a multiple of 10,␊ |
258 | ␉␉␉ (eg. if you want to set the bus ratio to 8.5, n will be␊ |
259 | ␉␉␉ 8.5*10=85), if set Acpipatcher will drop every ␊ |
260 | ␉␉␉ P-states with a bus ratio lower than n, ␊ |
261 | ␉␉␉ if n = 0, MinBusRatio = Disable.␊ |
262 | ␉␉ ␊ |
263 | P-States usage e.g: same as acpicodec ␉␉␉␉␉␉␉␉ ␊ |
264 | ␊ |
265 | C-States usage e.g: same as acpicodec ␊ |
266 | ␉␉␊ |
267 | ACPIDropTables usage e.g: same as acpicodec |